Unable to open a proper support request via this forum software when more than 2 stalwart-decribed URLs are mentioned

Issue Description

I’m trying to enter a support request in the “Questions” section here concerning issues I’m having with getting stalwart fully installed and operational.

In order to properly explain these problems, in the support request, I listed some stalwart-specified URL’s which trigger the errors.

However, this forum software will not allow me to post this support request, because it says that I cannot include more than 2 links.

These URL’s are NOT (!!!) meant to be treated as links!!! They are simply text which is necessary for describing the problems that I’m trying to find solutions for.

I tried marking these URL’s as preformatted text and as quoted text – and also as both of those at the same time – but none of these things caused this forum software to stop treating these text items as links.

How can I properly enter a support request which requires me to post more than two stalwart-specified URL’s which are triggering my support issues?

Expected Behavior

Ability to properly enter a support request via this stalwart support forum when the description of the support issue requires more than two stalwart-specified URL’s (as described in the stalwart docs) to be entered in order to give a meaningful description of the support issue.

Actual Behavior

Support request not accepted because it contains stalwart-specified URL’s that describe an installation problem I’m having, and it INCORRECTLY (!!!) treats those stalwart-supplied URL’s as “links” and prohibits posting the support request, because there are more than 2 of these stalwart-supplied URL’s that NEED (!!!) to be included in the support request in order to properly describe the problem I’m facing.

Reproduction Steps

(1) Start composing a support request here.
(2) Describe a problem that occurs with the stalwart-supplied (In the stalwart docs) URL’s that must be accessed in order to configure and run stalwart. Enter more than 2 of these stalwart-supplied URL’s
(3) Try to submit the support request. It will fail with a message that no more than 2 “links” can be present in a support request … even though these URL’s are NOT (!!!) meant to be used as links, but rather, as text that is necessry to describe the support issue

Relevant Log Output

Log output is irrelevant to this error. It’s an error with the stalwart forum software, not an error with the stalwart module itself.

Stalwart Version

v0.16.x

Installation Method

Binary (Linux)

Database Backend

RocksDB

Blob Storage

RocksDB

Search Engine

Internal

Directory Backend

Internal

I have reviewed the documentation and FAQ and confirm that my issue is NOT addressed there.

on

I have searched this support forum (open and closed topics) and confirm this is not a duplicate.

on

I understand that topics in this category are triaged by a bot first but a human reply will follow up. If I’d prefer a human-only reply, I’ll add the no-ai tag to my topic.

on

The two-link cap is a Discourse anti-spam rule for brand new accounts. It goes away on its own once the forum promotes you to the next trust level, which happens after you’ve read a handful of topics and spent a few minutes on the site.

You don’t have to wait for that, though. Discourse only counts real links, and nothing inside a code block becomes a link. Put the URLs in a fenced block, with the three backticks on lines of their own:

https://mail.example.org/admin
https://mail.example.org/.well-known/jmap

Single backticks around each URL work too: https://mail.example.org/admin. The quote and preformatted buttons in the editor don’t always produce a real code block, which would explain why those attempts were still blocked. If anything still gets through as a link, dropping the https:// part avoids it as well.

Post the installation question whenever you’re ready and I’ll take a look.

Thank you very much for explaining about the fact that we can “protect” those URL’s by enclosing them in code blocks.

I will soon once again try to post my support request, this time using those back-ticks.

I just now tried to re-post my support request, and this time, I enclosed each and every one of the standard, stalwart-supplied URL’s in back-ticks.

But sadly, I still am getting this same error about not being able to post more than 2 links.

And now, I retried posting the support request yet again, but this time, I left off all URL prefixes, and instead, I followed each truncated URL representation with text that states whether it’s an SSL or non-SSL URL.

And yet again, I am getting the same error about posting more than 2 “links”.

Could this forum software somehow be “remembering” any of my earlier failed attempts to post my support request and using that old, no-longer-being-posted text to make the “more than 2 links” determination?

It’s now been nearly 24 hours since I first posted here about my inability to submit a stalwart support request due to “more and 2 links”, and during that time, I have tried and reported the results all of the suggested remedies … and all failed.

Furthermore, no one has followed up to help me with this issue after the first response which offered those “solutions” that I tried and which didn’t work.

This inability of mine to get support here has now convinced me to totally give up on stalwart. I have now uninstalled it from my machine.

And I don’t plan to try stalwart again in the future, nor to post any more communication attempts here.

Community support is free support that is provided without any guarantees on response times.